Securitron iMXDa_iEXDa QUICK START GUIDE Uživatelský manuál stáhnout pdf

Securitron Magnalock Corp. Tel 775.355.5625

550 Vista Boulevard Fax 775.355.5633

Sparks, NV 89434 info@securitron.com

www.securitron.com

Page 1 Rev. B, 01/10

ASSA ABLOY, the global leader

in door opening solutions

iMXDa/iEXDa QUICK START GUIDE

PRODUCT OVERVIEW

MODEL iMXDa/iEXDa

Holding Force

1200 Lbs 544kg]

Dimensions: Length

12.5" [318mm]

Height 3.63" [92mm]

Depth 2" [51mm]

Dual Voltage 12/24 Volts DC

Current: @ 12VDC 370mA

@ 24VDC 270mA

RECOMMENDED TOOLS

Hammer

Center Punch

Power Drill

Drill bits: 9/64”, 3/16”, 7/32”, 3/8”, and 1/2” (iEXDa)

or 1” (iMXDa) diameters

Wrenches: 7/16” open end (or adjustable), 1/2” box/

open end (or adjustable), 1-1/4” open end

(or 12” adjustable), 3/16” Hex Key (Allen)

and provided 3/32” Hex Key

Pliers, vise grip

Screwdrivers: #1, #2 and #3

Phillips and 1/8” Flat Blade

Masking tape

Fish Tape or Lead Wire

Wire Strippers/Cutter

Multimeter

INSTALLATION

Mounting Configuration

Figure 1 illustrates a common installation on out-swing doors. The lock housing mounts to the

header near the corner opposite the door hinge side. The unit may be mounted horizontally or

vertically. Please use the included product mounting template and the following step-

by-step instructions to successfully install the lock housing and strike.

Figure 1

Typical Section of Installation (iMXDa shown)

To properly install the iMXDa/iEXDa unit, the following conditions should be verified:

The entire mounting area for the lock bracket and housing must be a flat surface.

The installed strike must allow the door to close properly.

 The lock (E-laminate) face and strike plate must be aligned so that they are centered.

STRIKE/LOCK ALIGNMENT IS IMPORTANT FOR LOCK SYSTEM STATUS SENSING FUNCTIONS

Sex Bolt & Strike

Mounting Screw

Door Frame & Stop

Door

Strike Plate

Lock Housing

Standard Sex

Bolt

(iEXDa)

Mounting Bracket

Lock Housing

Actuator

Hardware Pack

MXD Sex

Bolt

(iMXDa)

SFP (Not Included)

Mounting Bracket

and Hardware

Rubber Washers

(DPS) Strike

Plate

This Kit Includes

1 2 3 4

Shrnutí obsahu

Strany 1 - ASSA ABLOY, the global leader

Strany 2

PN# 500-22310Page 2 Rev. B, 01/10STEP 1 - MOUNTING THE STRIKE PLATEThe strike plate should be mounted prior to the lock housing. Figure 2 below illust

Strany 3

PN# 500-22310Page 3 Rev. B, 01/1022.Pull on the assembly (strike) to align and engage the knurled potion of the sex bolt into thehole.23.While keeping

Strany 4 - Page 4 Rev. B, 01/10

PN# 500-22310Page 4 Rev. B, 01/1011.Assemble the lock back onto the mounting bracket, then using a 3/32” hex wrench tightenthe three (3) set screws al

Komentáře k této Příručce

Žádné komentáře

Securitron iMXDa_iEXDa QUICK START GUIDE Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Pro domov Securitron iMXDa_iEXDa QUICK START GUIDE. Securitron iMXDa_iEXDa QUICK START GUIDE User Manual [it] Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Pro domov Securitron iMXDa_iEXDa QUICK START GUIDE